01 > ȸҰ

 
작성일 : 12-08-09 13:14
ELS-SDMV210(Samsung S5PV210) 보드에 커널 2.6.35.7 부팅 하기
 글쓴이 : 이로직…
조회 : 6,687  
U-Boot 1.3.4 (May 31 2012 - 17:43:50) for elogics-S5PV210M Rev.01


CPU: S5PV210@800MHz(OK)
APLL = 800MHz, HclkMsys = 200MHz, PclkMsys = 100MHz
MPLL = 667MHz, EPLL = 80MHz
HclkDsys = 166MHz, PclkDsys = 83MHz
HclkPsys = 133MHz, PclkPsys = 66MHz
SCLKA2M = 200MHz
Serial = CLKUART
Board: elogics-S5PV210
DRAM: 512 MB
SD/MMC: 942MB
NAND: 512 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
ELS-S5PV210M>setenv bootargs init=/init console=ttySAC1,115200 root=/dev/nfs rw nfsroot=192.168.1.20:/nfsroot/RootFS-S5PV210-Xwindows ip=192.168.1.252:192.168.1.20:192.168.1.1:255.255.255.0::eth0:off ethaddr=00:40:5c:26:0a:5b
ELS-S5PV210M>BOOT
Unknown command 'BOOT' - try 'help'
ELS-S5PV210M>boot
smc911x: initializing
smc911x: detected LAN9220 controller
smc911x: phy initialized
smc911x: MAC 00:40:5c:26:0a:5b
TFTP from server 192.168.1.20; our IP address is 192.168.1.100
Filename 'zImage'.
Load address: 0x20008000
Loading: T #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########################################
done
Bytes transferred = 3199384 (0x30d198)
Boot with zImage

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 2.6.35.7 (root@elogics-desktop) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #53 PREEMPT Wed Aug 8 20:41:50 KST 2012
CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDKV210
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41001099
Memory policy: ECC disabled, Data cache writeback
CPU S5PV210/S5PC110 (id 0x43110220)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
S5PV210: PLL settings, A=800000000, M=667000000, E=80000000 V=54000000
S5PV210: ARMCLK=800000000, HCLKM=200000000, HCLKD=166750000
HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
sclk_dmc: source is sclk_a2m (0), rate is 200000000
sclk_onenand: source is hclk_dsys (1), rate is 166750000
sclk: source is mout_mpll (6), rate is 66700000
sclk: source is mout_mpll (6), rate is 66700000
sclk: source is mout_mpll (6), rate is 66700000
sclk: source is mout_mpll (6), rate is 66700000
sclk_mixer: source is sclk_dac (0), rate is 54000000
sclk_spdif: source is sclk_audio (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_fimc: source is ext_xtal (0), rate is 24000000
sclk_cam0: source is ext_xtal (0), rate is 24000000
sclk_cam1: source is ext_xtal (0), rate is 24000000
sclk_fimd: source is ext_xtal (0), rate is 24000000
sclk_mmc: source is mout_mpll (6), rate is 47642857
sclk_mmc: source is mout_epll (7), rate is 80000000
sclk_mmc: source is mout_mpll (6), rate is 47642857
sclk_mmc: source is mout_epll (7), rate is 80000000
sclk_mfc: source is sclk_a2m (0), rate is 200000000
sclk_g2d: source is sclk_a2m (0), rate is 200000000
sclk: source is sclk_a2m (0), rate is 200000000
sclk_csis: source is ext_xtal (0), rate is 24000000
sclk_spi: source is ext_xtal (0), rate is 24000000
sclk_spi: source is ext_xtal (0), rate is 24000000
sclk_pwi: source is ext_xtal (0), rate is 24000000
sclk_pwm: source is ext_xtal (0), rate is 24000000
sclk_mdnie: source is ext_xtal (0), rate is 24000000
sclk_mdnie_pwm: source is ext_xtal (0), rate is 24000000
s5pv210: 37748736 bytes system memory reserved for mfc at 0x2091a000
s5pv210: 37748736 bytes system memory reserved for mfc at 0x22d1a000
s5pv210: 6291456 bytes system memory reserved for fimc0 at 0x2511a000
s5pv210: 10137600 bytes system memory reserved for fimc1 at 0x2571a000
s5pv210: 6291456 bytes system memory reserved for fimc2 at 0x260c5000
s5pv210: 8388608 bytes system memory reserved for jpeg at 0x266c5000
s5pv210: 6144000 bytes system memory reserved for fimd at 0x26ec5000
s5pv210: 8388608 bytes system memory reserved for g2d at 0x274a1000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: init=/init console=ttySAC1,115200 root=/dev/nfs rw nfsroot=192.168.1.20:/nfsroot/RootFS-S5PV210-Xwindows ip=192.168.1.252:192.168.1.20:192.168.1.1:255.255.255.0::eth0:off ethaddr=00:40:5c:26:0a:5b
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 134328k/134328k available, 127816k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xff000000 - 0xffe00000 ( 14 MB)
vmalloc : 0xd0800000 - 0xfc000000 ( 696 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0033000 ( 172 kB)
.text : 0xc0033000 - 0xc060b000 (5984 kB)
.data : 0xc060c000 - 0xc06555e0 ( 294 kB)
SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:393
VIC @fd000000: id 0x00041192, vendor 0x41
VIC @fd010000: id 0x00041192, vendor 0x41
VIC @fd020000: id 0x00041192, vendor 0x41
VIC @fd030000: id 0x00041192, vendor 0x41
mult[140737]
max_delta_ns[2937815369]
min_delta_ns[30517]
rate[32768]
HZ[256]
Console: colour dummy device 80x30
console [ttySAC1] enabled
Calibrating delay loop... 796.20 BogoMIPS (lpj=1556480)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys debug
Initializing cgroup subsys cpuacct
Initializing cgroup subsys freezer
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
spi============master register
S3C Power Management, Copyright 2004 Simtec Electronics
pmstats at 00000000
smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
smdkc110_setup_clocks: sclk_mmc: source is mout_mpll, rate is 47642857
S5PV210: Initializing architecture
s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0
s3c24xx-pwm s3c24xx-pwm.1: tin at 66700000, tdiv at 66700000, tin=divclk, base 8
s3c24xx-pwm s3c24xx-pwm.2: tin at 66700000, tdiv at 66700000, tin=divclk, base 12
s3c24xx-pwm s3c24xx-pwm.3: tin at 66700000, tdiv at 66700000, tin=divclk, base 16
regulator: pd_audio_supply: 5000 mV normal
regulator: pd_cam_supply: 5000 mV normal
regulator: pd_tv_supply: 5000 mV normal
regulator: pd_lcd_supply: 5000 mV normal
regulator: pd_g3d_supply: 5000 mV normal
regulator: pd_mfc_supply: 5000 mV normal
bio: create slab at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.23.
Switching to clocksource clock_source_systimer
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 128 (order: 0, 6144 bytes)
UDP-Lite hash table entries: 128 (order: 0, 6144 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PMU: registered new PMU device of type 0
SMDKC110/V210 RTC, (c) 2010 Samsung Electronics
smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
smdkc110-rtc smdkc110-rtc: rtc core: registered s3c as rtc0
S5PV210 ADC driver, (c) 2010 Samsung Electronics
cpuidle: phy_regs_save:0x2fd3c000
Loaded driver for PL330 DMAC-0 s3c-pl330
DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32
Loaded driver for PL330 DMAC-1 s3c-pl330
DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
Loaded driver for PL330 DMAC-2 s3c-pl330
DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
ashmem: initialized
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 262
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
s3cfb s3cfb: [fb2] dma: 0x26ec5000, cpu: 0xd1000000, size: 0x005dc000
Console: switching to colour frame buffer device 100x30
FIMD src sclk = 166750000
s3cfb s3cfb: registered successfully
PA FB = 0x26EC5000, bits per pixel = 32
screen width=800 height=480 va=0xc6ec5000 pa=0x26ec5000
xres_virtual = 800, yres_virtual = 1920, xoffset = 0, yoffset = 0
fb_size=6144000
Back frameBuffer[0].VAddr=c703c000 PAddr=2703c000 size=1536000
Back frameBuffer[1].VAddr=c71b3000 PAddr=271b3000 size=1536000
Back frameBuffer[2].VAddr=c732a000 PAddr=2732a000 size=1536000
s5pv210-uart.0: s3c2410_serial0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
s5pv210-uart.1: s3c2410_serial1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
s5pv210-uart.2: s3c2410_serial2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
s5pv210-uart.3: s3c2410_serial3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
Android kernel panic handler initialized (bind=kpanic)
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
Creating 4 MTD partitions on "s5pv210-nand":
0x000000000000-0x000000040000 : "bootloader"
0x000000040000-0x000000400000 : "kernel"
0x000000400000-0x000003400000 : "rootfs"
0x000003400000-0x000020000000 : "File System"
spi_gpio_init: spi_gpio_init ====================
s3c64xx_spi_probe: =====================1
spi_register_master: 1
spi_register_master: 2
spi_register_master: 3
spi_register_master: 4
spi_register_master: registered master spi0
scan_boardinfo: scan_boardinfo: c busnum = 0, m busnum = 0
spi_setup: 1
spi_setup: 2
spi_setup: 3
s3c64xx_spi_setup: 1
s3c64xx_spi_setup: 2
s3c64xx_spi_setup: 3
s3c64xx_spi_setup: 4
s3c64xx_spi_setup: 5
s3c64xx_spi_setup: 6
s3c64xx_spi_setup: speed = 8337500, max_speed = 10000000
spi_setup: 4
spi_setup: setup mode 0, 8 bits/w, 8337500 Hz max --> 0
scan_boardinfo: scan_boardinfo: c busnum = 1, m busnum = 0
spi_register_master: 5
s3c64xx_spi_probe: Samsung SoC SPI Driver loaded for Bus SPI-0 with 1 Slaves attached
s3c64xx_spi_probe: IOmem=[0xe13000ff-0xe1300000] DMA=[Rx-22, Tx-23]
s3c64xx_spi_probe: =====================1
spi_register_master: 1
spi_register_master: 2
spi_register_master: 3
spi_register_master: 4
spi_register_master: registered master spi1
scan_boardinfo: scan_boardinfo: c busnum = 0, m busnum = 1
scan_boardinfo: scan_boardinfo: c busnum = 1, m busnum = 1
spi_setup: 1
spi_setup: 2
spi_setup: 3
s3c64xx_spi_setup: 1
s3c64xx_spi_setup: 2
s3c64xx_spi_setup: 3
s3c64xx_spi_setup: 4
s3c64xx_spi_setup: 5
s3c64xx_spi_setup: 6
s3c64xx_spi_setup: speed = 6000000, max_speed = 10000000
spi_setup: 4
spi_setup: setup mode 0, 8 bits/w, 6000000 Hz max --> 0
spi_register_master: 5
s3c64xx_spi_probe: Samsung SoC SPI Driver loaded for Bus SPI-1 with 1 Slaves attached
s3c64xx_spi_probe: IOmem=[0xe14000ff-0xe1400000] DMA=[Rx-24, Tx-25]
spi_match_device: drv->name = spidev
spi_match_device: drv->name = spidev
smsc911x: Driver version 2008-10-21.
=======================smsc.......
smsc911x-mdio: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1)
net eth0: MAC Address: a6:8c:3e:aa:db:94
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
s5p-ehci s5p-ehci: s5pv210 EHCI
s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
failed to find udc vcc source
s3c-usbgadget: probe of s3c-usbgadget failed with error -2
s3c-udc : S3C HS USB Device Controller Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android init
android_probe pdata: c0619c98
f_adb init
android_register_function adb
f_mass_storage init
fsg_probe pdev: c0618b10, pdata: c0619cbc
android_register_function usb_mass_storage
f_rndis init
android_register_function rndis
mice: PS/2 mouse device common for all mice
input: torbreck-key as /devices/virtual/input/input0
torbreck-key torbreck-key.0: aesop keypad input driver Initialized!!
S5P Touchscreen driver, (c) 2008 Samsung Electronics
KEY PRESSED : KEY_DOWN
KEY PRESSED : KEY_ENTER
KEY PRESSED : KEY_RIGHT
KEY PRESSED : KEY_LEFT
KEY PRESSED : KEY_UP
KEY PRESSED : KEY_HOME
KEY PRESSED : KEY_POWER
S5P TouchScreen got loaded successfully : 12 bits
input: S5P TouchScreen as /devices/virtual/input/input1
using rtc device, s3c, for alarms
i2c /dev entries driver
Linux video capture interface: v2.00
s3c-csis: Samsung MIPI-CSI2 driver probed successfully
mfc_init: <6>S5PC110 MFC Driver, (c) 2009 Samsung Electronics

S3C JPEG Driver, (c) 2007 Samsung Electronics
JPEG driver for S5PV210
i2c i2c-1: attached s5p_ddc into i2c adapter successfully
S5PC11X HPD Driver, (c) 2009 Samsung Electronics
S5PC11X CEC Driver, (c) 2009 Samsung Electronics
s3c_bat_init
sec-fake-battery sec-fake-battery: s3c_bat_probe
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133400000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)
s3c-sdhci s3c-sdhci.3: clock source 1: hsmmc (133400000 Hz)
s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
logger: created 64K log 'log_system'
s3c2412_snd_txctrl: s3c2412_snd_txctrl(0)
asoc: WM8580 PAIFRX <-> s3c64xx-i2s-v4 mapping ok
asoc: WM8580 PAIFTX <-> s3c64xx-i2s-v4 mapping ok
asoc: WM8580 PAIFRX <-> i2s-sec-fifo mapping ok
ASoC: Failed to create Rear-L/R debugfs file
ASoC: Failed to create Center/Sub debugfs file
ASoC: Failed to create Front-L/R debugfs file
ALSA device list:
#0: smdk (WM8580)
GACT probability NOT on
Mirror/redirect action on
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2098 buckets, 8392 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
NET: Registered protocol family 15
ThumbEE CPU extension supported.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
regulator_init_complete: disabling pd_mfc_supply
regulator_init_complete: disabling pd_tv_supply
regulator_init_complete: disabling pd_cam_supply
smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
smdkc110-rtc smdkc110-rtc: setting system clock to 2010-01-01 12:00:01 UTC (1262347201)
FIMC0 registered successfully
FIMC1 registered successfully
FIMC2 registered successfully
<6>S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
s5p-tvout s5p-tvout: hpd status is cable removed
mmc0: new SD card at address ceff
mmcblk0: mmc0:ceff SU01G 942 MiB (ro)
mmcblk0: p1
net eth0: SMSC911x/921x identified at 0xd08a4300, IRQ: 38
IP-Config: Complete:
device=eth0, addr=192.168.1.252, mask=255.255.255.0, gw=192.168.1.1,
host=192.168.1.252, domain=, nis-domain=(none),
bootserver=192.168.1.20, rootserver=192.168.1.20, rootpath=
DBUG_PORT must not use AFC!
Looking up port of RPC 100003/2 on 192.168.1.20
Looking up port of RPC 100005/1 on 192.168.1.20
VFS: Mounted root (nfs filesystem) on device 0:12.
Freeing init memory: 172K
Failed to execute /init. Attempting defaults...
EXT3-fs: barriers not enabled
EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode
kjournald starting. Commit interval 5 seconds
Executing mount /dev/mmcblk0p1 to /media/mmcblk0p1, action=
smdkc110-rtc smdkc110-rtc: rtc disabled, re-enabling
EXT3-fs: barriers not enabled
EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode
kjournald starting. Commit interval 5 seconds
Executing mount /dev/mmcblk0p1 to /media/mmcblk0p1, action=add
INIT: Entering runlevel: 5
Starting Dropbear SSH server: dropbear.
Starting system message bus: dbus.
Starting syslogd/klogd: done
Starting Connection Manager
Starting GPE display manager: gpe-dm

_____ _____ _____ _____ _____
| _ | __| __| | _ |
| | __|__ | | | __|
|__|__|_____|_____|_____|__|.or.kr

(C)2010 aESOP Embedded Forum.
aESOP S5PCV210 Embedded Linux Platform. (1010)

System : S5PC1xx
Console : s3c2410_serial1

S5PC1xx login: root
root@S5PC1xx:~#